The Maytag washer in the spin cycle spins the clothes around at a high speed to remove water from them. This fast-spinning action forces the water out of the clothes rapidly. The washer then spins the clothes in the opposite direction to remove any remaining water.
This fast-paced spin cycle can be noisy and may cause the machine to vibrate. This is normal and is not a cause for concern until you notice your Maytag washer shaking violently on the spin cycle.
Maytag Washer Shaking Violently On Spin Cycle
When your Maytag washer vibrates excessively during a spin cycle, it can cause damage to the machine as well as the structure it is sitting on. The main damage that can occur is to the washer’s legs or leveling feet, which can become damaged or even broken over time.
If you leave your Maytag washing machine unleveled, its noisy vibrations can also damage the washer’s tub, which can lead to leaks. Additionally, the vibration can cause the washer to walk across the floor, which can also damage the flooring.
Moreover, your washer can become noisy due to constant vibrations. Therefore, there are many reasons you would not want your Maytag washer to shake violently during the spin cycle.
You May Also Like: How To Replace Washing Machine Balance Ring That Vibrates Excessively
Why Is My Maytag Top Load Washer Shaking Violently On The Spin Cycle?
Below are some of the reasons that can make your Maytag washer shake violently on the spin cycle. We have also provided a doable solution for every problem that you can perform easily at home to fix your shaking Maytag washer.
1. Unbalanced or undistributed Load
If your washer is vibrating excessively during the spin cycle, it is likely due to an unbalanced load.
This means that the weight of the laundry in the tub is not evenly distributed. When this happens, your Maytag washer will spin faster and harder in an attempt to balance the load, which can cause it to vibrate excessively.
Also note that if your new Maytag washer is shaking violently on spin cycle, most of the time this is the case.
Don’t worry there are a few things you can do to fix this problem.
First, try redistributing the laundry in the tub so that it is more evenly balanced. You can also try adding a few towels to the load to help balance it out. If the problem persists, you may need to reduce the load.
2. Overloading The Tub Than Capacity
If your Maytag Top Load Washing Machine is vibrating or shaking during the spin cycle, it is likely due to an overloaded tub. When the tub is overloaded, the washer’s balance goes out of order and it cannot remove all the water from the clothing.
To fix this problem, you will need to remove some of the clothing from the washing machine and redistribute the load evenly. For this purpose, the manual can hint you the exact load you can spin at a time.
3. Faulty/Stretched Suspension Springs
Suspension springs suspend the drum assembly from its compartment and are completely different than shock absorbers. The springs are located under the washer tub and support the tub during the washing cycle.
Over time, these springs can become weakened or broken, which can cause the Maytag washer to vibrate or shake. If you notice your washer shaking or vibrating more than usual, it’s likely that the suspension springs need a replacement.
Faulty or stretched suspension springs are one of the most common causes of Maytag washer shaking on the spin cycle. With the washer shaking violently it can even lead to damage to the washer or clothing.
Therefore, it’s important to check the suspension springs and make sure they are not stretched.
Replacing these springs is usually a fairly simple, inexpensive, and easy-to-do task.
How To Replace Suspension Springs On The Maytag Washer?
So if your Maytag washer is not draining properly or is making noise, it may be time to replace the suspension springs.
Before you begin, you’ll need to purchase the correct replacement springs for your specific model of Maytag washer. You can find this information in the owner’s manual or by contacting Maytag customer service.
Once you have the correct springs, follow these steps to replace the suspension springs on your Maytag washer:
1. Unplug the washer from the power outlet.
2. Tip the washer back on its side so that you can access the suspension springs.
3. Use a pair of pliers to remove the old springs.
4. Attach the new springs in the same position as the old ones.
5. Tip the washer back upright and plug it back in.
4. Uneven Stand Can Be The Reason For Shaky Maytag Washer
If your washing machine is vibrating excessively, it is likely because the legs or the surface beneath them is not even. Uneven legs can cause the washer to shake and vibrate during the spin cycle because it became un capable of balancing itself.
First, you should check for any unkind movement by rocking your Maytag washer to fix this problem. If not a single leg is broken or damaged, you will need to level the legs of the washer. You can do this by adjusting the leveling feet or blocks until the washer is level.
Once the washer is level, the vibrations should stop.
5. Broken or Worn-out Shock Absorber
Like shocks in your bike or car, shocks in a washer help to dampen the vibration of the tub during the spin cycle. When your Maytag washer shocks are worn out, they can no longer effectively prevent the vibration, causing the washer to shake and vibrate heavily.
This can cause problems with the washer’s performance and can also lead to damage to the washer itself. If you suspect your washer’s shocks may be worn out, it is best to replace them as soon as possible.
How To Check Or Replace Broken or Worn-out Shock Absorbers
Before you try to change the shock absorbers, it is best to check whether it is the cause of excessive vibrations in your washing machine or not. For this purpose do this:
- Unplug your washing machine from the power socket.
- Before you proceed further, it is advisable to empty the washing machine of dirty clothes and water.
- Open up the cabinet of your Maytag machine with a screwdriver.
- When you get the panel open, check for signs of leaks or cracks in all parts of the panel and shocks.
- If there are any, then likely that this is where additional vibration can cause them to expand.
- The next thing to do is check if the suspension rods or suspension springs need replacing by looking for major signs of wear and tear on them.
- If any of them show these signs, then look no further as this is your problem.
- Remove these old parts and replace them with new parts that you would acquire from one of your local home improvement stores along with spare parts for your model (your owner’s manual should have details as to how to fit these).
- Always note: If a single or more than one shock absorber are damaged or worn out, it is advised to change all of them at once.
Once done, re-assemble everything back together in reverse order like how you did when disassembling everything. Check before putting something together if the holes which hold all the screws line up properly so that nothing goes out of place.
6. The Suspension Rod Might Be Broken Or Damage
Suspension rods are an important part of a Maytag washer. They are responsible for supporting the washer tub and keeping it level during the wash cycle. If a suspension rod is damaged or broken, it can cause the washer tub to become unbalanced and result in a noisy or shaking washer.
What to do if a suspension rod of a Maytag washer is damaged or broken?
If the suspension rod of your Maytag washer is not in a good shape or form, it is important to take immediate action to solve the problem. Depending on the severity of the damage, you may be able to fix the problem yourself.
However, if the damage is significant, it is best to contact a qualified appliance repair technician.
If you decide to attempt a repair on your own, be sure to disconnect the power to the washer before beginning any work.
After disconnecting the power, you will need to remove the washer tub. You can do this by removing a few screws that hold the tub in place.
Once the tub is removed, you will be able to access the suspension rod. Inspect the rod for any damage and replace it if necessary.
Once the new rod is in place, you can reassemble the washer and reconnect it to the power.
7. Damaged Snubber Pad Causes Maytag Washer To Shake Violently On Spin Cycle
A snubber pad is also a type of shock absorber that is used in Maytag washing machines. It is a small, often triangular-shaped piece of padding that is located near the edge of the washer tub.
It helps to cushion the washer during the spin cycle and can prevent damage to the washer’s internal components. The snubber pad can also help to reduce noise and vibration during the spin cycle.
So if your Maytag washer is shaking violently on the spin cycle then inspect the snubber pad. If it is damaged, worn out, or otherwise not performing properly, it will need to be replaced.
8. Broken Balance Ring causes the Maytag Washer to Shake Violently On Spin Cycle
The balance ring is located around the outer edge of the washing machine tub. It helps to keep the tub balanced during the spin cycle with the fluid inside it. When the balance ring is damaged or broken, it can cause the tub to become unbalanced, which will cause the washing machine to shake heavily and violently.
A broken balance ring can cause serious damage to the washing machine and even to your home if the washing machine is not properly supported. So if your Maytag washer is shaking violently on the spin cycle then inspect the balance ring. If it is leaking, damaged, worn out, or otherwise not performing properly, replace it.
9. Counter Balance Spring Might Be The Reason
A damaged or broken counterbalance spring in a Maytag washer can cause the washer to shake violently during the spin cycle. This can be a very dangerous situation, as the washer can easily tip over or break if it is not properly balanced.
These springs help to keep the washer balanced during the spin cycle because they absorb all the vibrations of the machine.
So when it is damaged or broken, the washer can become unbalanced and shake. This can cause the washer to tip over or break, which can be a very dangerous situation. If you have a Maytag washer with a damaged or broken counterbalance spring, you should have it repaired or replaced as soon as possible.
10. Shipping Bolts May Cause Maytag Washer To Shake Excessively
Shipping bolts are inserted into the shipping container to secure the Maytag washer during transit. However, if these bolts are not removed before use, they can cause the washer to vibrate excessively during the spin cycle.
This is because the bolts are not balanced and will cause the washer to wobble as it spins. If you experience this issue, simply remove the shipping bolts and your washer should operate as normal.
11. Rear Drum With Bearing
Another common cause for a Maytag washing machine to vibrate excessively during the spin cycle is an issue with the rear drum with the bearing.
The rear drum is what holds the washing machine’s washing basket in place with the help of one or more bearings. If the bearing system becomes defective, it causes your Maytag washer to shake violently during the spin cycle.
If you think that the problem with your washer is due to the rear drum, you will need to replace the bearings and the outere drum all at once.
FAQs – Maytag Washer Shaking Violently On Spin Cycle
How to stabilize a washing machine?
If your washing machine is wobbling or shaking, it could be due to a number of different factors. In most cases, you can stabilize your washing machine by adjusting the legs. However, if the legs are not adjustable or the machine is still wobbling, there are a few other things you can try.
First, check to see if the washing machine is level. If it’s not, you can try to level it by placing thin books or boards under the legs. You can also try to level the machine by redistribution of the load. If the washing machine is still wobbling, you may need to reduce the load.
How to balance a washer drum?
If your Maytag washer isn’t balanced, it can vibrate and damage both the washer and your laundry. To avoid this, it’s important to know how to properly balance a washer drum.
Luckily, it’s not difficult to do. Start by checking the level of your washer. If it’s not level, adjust the legs until it is. Next, open the lid and add a few items of laundry to the drum. Close the lid and start the washer on a gentle cycle.
If the washer is still vibrating, try adding a few more items of laundry. Once the washer is balanced and running smoothly, you can do a full load of laundry as normal.
How do I install anti-vibration pads on the Maytag washing machine?
Washing machines are notoriously noisy, so it’s no surprise that many people look for ways to reduce the noise their machine makes.
One popular solution is to install anti-vibration pads on the machine. Anti-vibration pads are designed to absorb vibrations and reduce the noise that your machine makes.
Installing anti-vibration pads is relatively simple and can be done in just a few steps.
- First, you’ll need to purchase the pads. You can find them at most hardware stores.
- Once you have the pads, measure the area where they will be installed.
- Then clean the surface where you want to put them.
- Next, you’ll need to peel the backing off the new pads and stick them in place.
- Finally, re-install the Maytag washer on the pads.
Why you must level the legs of a new Maytag washing machine?
Before starting a new Maytag washing machine, it is necessary to level the legs. This is to ensure that the new machine does not vibrate excessively during operation.
If the machine is not level, it can cause undue stress on the internal components, which can lead to premature failure. In addition, excessive vibration can also cause your new washing machine to walk or move around during operation, which can be dangerous.
Why does my Maytag bravos washer shake violently on the spin cycle?
The Maytag Bravos is a top-loading washing machine that is known for its efficiency and reliability. However, some users have reported that their Bravos washer shakes violently during the spin cycle.
If your Maytag Bravos washer is shaking violently during the spin cycle, there are several possible causes.
- First, check to see if anything is caught in the washer’s drum. Sometimes items like coins or buttons can become lodged in the machine and cause it to shake.
- If there’s nothing caught in the drum, the next step is to check the washer’s legs. Make sure all four legs are firmly attached to the floor and that the washer is level.
- If the washer is still shaking, it’s possible that the washing machine’s load is unbalanced. Try redistributing the laundry items in the machine and starting the spin cycle again.
I would like to thank you for reading my work on addressing the causes and their possible solutions for Maytag washers shaking violently on the spin cycle. I am confident that your issue has now been resolved and that your washer is now safe to use.
Always remember that it is important to make sure that your washer is installed correctly and leveled properly before using it to avoid problems such as your washer.
In conclusion, there are several potential solutions for the problem of a Maytag washer shaking violently on the spin cycle. You can easily fix most of these problems at home following our guide. With a little patience and smart work, any of these solutions should fix the problem so that your washer can operate smoothly and efficiently during spinning.